Parkside PET 25 B1 Manuel d'utilisateur télécharger pdf (Page 33)

33 GB/MT

tacker may be accidentally activated if it is

plugged in.

Use caution while removing a jammed

fastener. The mechanism may be under com-

pression and the fastener may be forcefully

discharged while attempting to free a jammed

condition.

Do not use this tacker for fastening elec-

trical cables. It is not designed for electric ca-

ble installation and may damage the insulation

of electric cables thereby causing electric shock

or ﬁre hazards.

Safety advice relating speciﬁ-

cally to Electric nailer / staplers

DANGER OF INJURY! Never point the de-

vice at yourself or at other people or animals.

Ensure that no people or animals are on the

other side of the workpiece.

PROTECT YOUR EYES! Wear protective

glasses. This also applies to people who may

be helping with the work by supporting or

holding the workpiece.

Make sure the device is switched oﬀ before

you load the magazine. Set the ON / OFF

switch to position “0” and pull the mains plug

out of the mains socket!

Do not use the device to ﬁx electrical cabling

in place.

Secure the workpiece. A workpiece held in a

clamp or vice is kept more securely in place

than one held by your hand.

Always work with the mains lead leading away

from the rear of the device.

DANGER OF INJURY! Use the device with

only the staples and nails speciﬁed above.

Ensure that the staples or nails do not project

from the surface of the workpiece or penetrate

through to the other side.

Short-term operation time: Let the device cool

down after 15 minutes of continuous operation.

DANGER OF INJURY! Keep your ﬁngers and

other body parts away from the front plate

Never ﬁre staples or nails through the air. At

short range the shot staples or nails could lead

to serious injury.

Only soft materials such as wood or textiles

should be joined using the device. Otherwise

the device could be damaged.

CAUTION! Connect the device to the mains

only when it is switched oﬀ. Set the ON / OFF

switch

to position “0”.

DANGER OF INJURY!

Switch the device on just before you intend to

use it. If you are not using the device, switch it

oﬀ to prevent unintentional ﬁring.

Before use

Loading the magazine

Squeeze the end of the magazine slider

(see Fig. A).

Pull the magazine slider

out of the magazine

(see Fig. B).

Fill the magazine

with staples or nails

(see Fig. C).

Note on filling with nails: Use the right-

hand slot for ﬁlling with nails as shown in the

detailed image in Fig. C. Ensure that the nail

heads are all at the top.

NOTE: Observe the maximum capacity of ap-

prox. 85 staples or approx. 75 nails when ﬁlling.

After ﬁlling, push the magazine slider

into

the magazine

as far as it will go until you

hear and feel it engage.

NOTE: The magazine ﬁlling level indicator

allows you to see whether there are still staples

in the magazine.

Setting the impact force

NOTE: Select the lowest impact force necessary

for your stapling.

Take into account the length of the staples or nails

to be used and the strength of the materials to be

joined.

Impact force controller

Increase impact force:

Turn the impact force controller

anticlockwise.

Safety instructions for tackers / Before useGeneral power tool safety warnings / Safety instructions for tackers

1 2 ... 28 29 30 31 32 33 34 35 36 37 38 ... 44 45

Commentaires sur ces manuels

Pas de commentaire

Parkside PET 25 B1 Manuel d'utilisateur Page 33

Commentaires sur ces manuels

Produits connexes et manuels pour Outils électriques Parkside PET 25 B1